error codes found
AEG Induction Hob: Power Level Number Flashes ("12")
When the power level flashes, typically at the number 12, on an AEG induction hob, it means the selected zone can't activate the induction coil because it doesn't detect a suitable pan.
AEG Fridge Alarm AL01/AL02: Temperature Too High
AL01 warns that the fridge zone is too warm and AL02 that the freezer temperature is rising or already too high, with an audible alarm and a flashing symbol on the display.
AEG Washer Error E10: Water Inlet Fault
Triggers when the AEG washer fails to reach the required water level within the time limit set by the control electronics.
AEG Dryer Error E61: Insufficient Heating
The E61 code indicates the AEG dryer hasn't reached the expected drying temperature within the maximum allowed time, almost always due to poor ventilation or a heating element fault.
AEG Oven Error F11: Temperature Sensor Fault
The F11 code on an AEG oven means the NTC probe measuring internal temperature is sending an out-of-range signal, so the oven cannot regulate heat accurately.
AEG Extractor Hood: Grease Filter Saturation Alert
AEG hoods include a timer that lights up an icon or warning light after accumulating a set number of operating hours, signaling that the metal filters need cleaning.
AEG Dishwasher Error i30: Overflow Protection Triggered
AEG's Aqua-Control safety system has detected water in the base tray and triggers an emergency drain to prevent flooding in the kitchen.
Balay Oven Error E05-32: Temperature Probe Fault
The E05-32 code on a Balay oven appears when the probe measuring the cavity's internal temperature sends an out-of-range reading, and the oven halts cooking as a protective measure.
Balay Washer Error E23: Motor or Spin Fault
Appears when the control board detects the motor is not turning at the expected speed or not responding correctly during the spin phase.
Balay / Bosch Dishwasher Error E24: Drain Evacuation Failure
Dishwasher detects abnormal backpressure during initial drain sequence.
Balay Fridge Error F3: Evaporator Sensor Fault
The F3 code, along with the audible alarm, indicates on Balay fridges a fault in the sensor that controls evaporator temperature and manages defrost cycles.
Balay Microwave: "Door Open" Alert and No Heating
When a Balay microwave shows the door-open symbol or beeps without heating even though the door is closed, the safety switch system isn't confirming a proper close.
Beko Washer Error E02: No Water Intake
Shown when the Beko washer fails to fill with water within the expected time to start the program.
Beko Dishwasher Error E1: No Water Intake
Indicates the Beko dishwasher did not detect enough water during the initial fill and stops the cycle before washing begins.
Beko Refrigerator Error E4: Defrost Heater System Fault
Defrost sensor or evaporator heating element failed to defrost ice buildup during automatic cycle.
Beko Dryer Error Er04: Door Sensor Overheating
The Er04 code appears when the NTC sensor near the door detects the temperature has exceeded roughly 60°C, causing the dryer to stop the compressor for a few minutes as a safety measure.
Bosch Fridge Error E01/E02: Temperature Sensor Fault
E01 points to a fault in the fridge compartment sensor and E02 to the freezer sensor; the control board stops receiving a reliable temperature reading.
Bosch Dryer Error E:01: Heat Detection Fault
The E:01 code appears when the Bosch dryer's heating assembly sensor doesn't detect enough heat during the cycle, so the laundry doesn't dry properly.
Bosch Dishwasher Error E09: Water Heating Fault
Appears when the heating element or its temperature sensor is not working correctly, so the dishwasher fails to reach the program temperature.
Bosch Washer Error E18 / F18: Pump Blocked
Bosch electronics detect that water level is not dropping in time during drain phase.
Bosch Induction Hob Error E2: Overheat Protection
The Bosch induction hob cuts power to the cooking zone and displays E2 when its internal electronics reach too high a temperature and trigger automatic protection.
Bosch Microwave Error E-3: Automatic Door-Opening System Fault
On built-in Bosch microwaves with a motorized door-opening system, error E-3 means the electric mechanism that opens or closes the door failed to complete its travel correctly.
Bosch Oven Error E9: Overheat (ECO) Sensor Fault
Indicates the ECO safety sensor, which cuts power if the oven overheats, has detected an open circuit or abnormal reading and locks out operation as a safety measure.
Bosch Extractor Hood: "CL" Alert or Saturated Grease Filter Indicator
On Bosch hoods, the "CL" alert or filter icon that appears after a set number of usage hours means the metal grease filters need cleaning to keep suction performance up.
Candy Washer Error E03: Water Drain Problem
The Candy washer signals it could not complete draining the drum within the estimated time, almost always due to a clogged filter.
Candy Fridge Error E1: Defrost Sensor Fault
The E1 code on Candy fridges flags a fault in the temperature probe that controls the evaporator's automatic defrost cycle.
Candy Dishwasher Error E1: No Water Entering the Tub
The E1 code on a Candy dishwasher means the appliance doesn't detect the expected water level in the tub after the normal fill time has passed.
Candy Dishwasher Error E3: Overflow Protection Triggered
Indicates the safety float detected excess water in the base tray and stopped the cycle to prevent flooding.
Candy Oven Error ER02: Program Selector Fault
The ER02 code on a Candy oven means the program selector knob (mechanical or electronic) is sending an inconsistent signal to the board, preventing it from selecting or holding a cooking function.
Electrolux Fridge Error E01-E07: Sensor Warning
This family of codes (E01, E02, E03, E06, or E07) indicates one of the Electrolux fridge's temperature sensors has stopped sending a valid reading to the control board.
Electrolux Washer Error E20: Drain Fault
The E20 code means the Electrolux washer cannot drain the water from the drum within the expected time, usually due to a clogged filter or blocked hose.
Electrolux Dryer Error EF1: Thermal Limiter Tripped
The EF1 code indicates the safety thermal limiter has tripped because the dryer reached an excessive temperature, almost always due to restricted airflow.
Electrolux Oven Error F1: Door Lock Mechanism Fault
The F1 code on an Electrolux oven usually points to a problem with the mechanism or sensor that locks the door, either from a misaligned door or a fault in the latch itself.
Electrolux Extractor Hood: Grease Filter Indicator Lit
The grease filter indicator on an Electrolux hood turns on automatically after a set number of accumulated operating hours, signaling that the metal filters need cleaning.
Electrolux Dishwasher Error i20: Drain Fault
Shown when the Electrolux dishwasher fails to drain dirty water from the tub within the time set by the program.
Fagor Washer Error E03: Water Drain Fault
Indicates the Fagor washer could not drain water from the drum within the expected time, halting the program before spinning.
Fagor Oven Door Lock Fault: Pyrolysis Cycle Interrupted
The padlock symbol flashes on the Fagor oven panel because the door's thermal lock mechanism fails to confirm closure during the pyrolytic cleaning cycle, halting the program for safety.
Fagor Fridge Error NT1: Refrigerator Sensor Fault
The NT1 code on Fagor fridges indicates that the fridge compartment's temperature probe isn't sending a correct signal to the control board.
Haier Washer Error E1: Door Lock Fault
The E1 code on a Haier washer indicates the system cannot confirm the door is properly closed and locked before starting the wash cycle.
Haier Dishwasher Error E4: Water Drain Fault
Indicates the Haier dishwasher failed to drain dirty water from the tub within the time limit set by the program.
Haier Fridge Alarm H1 / H2: Temperature Out of Range
The Haier combi fridge shows H1 (fridge compartment) or H2 (freezer compartment) when internal temperature rises too much for an extended period.
Hotpoint Fridge Error E8: Evaporator Sensor Fault
The E8 code on Hotpoint fridges points to a problem with the thermistor sensor on the evaporator, which manages the automatic defrost cycles.
Hotpoint Washer Error F17: Door Lock Fault
Appears when the Hotpoint washer cannot confirm the door is properly closed and locked before starting or during the program.
Hotpoint Dishwasher Error F2: No Water Intake
The F2 code, along with a flashing tap symbol, indicates the Hotpoint dishwasher does not detect water entering at the start of the program.
Indesit Fridge Error E1: Refrigerator Sensor Fault
The E1 code on an Indesit fridge indicates a fault in the fridge compartment's temperature sensor, so the board cannot properly regulate cooling.
Indesit Oven Error F03: Temperature Sensing Fault
The F03 code on an Indesit oven points to a fault in the sensor that measures the cavity's internal temperature, which stops the oven from regulating heat correctly during cooking.
Indesit Washer Error F05: Drain Pump Fault
Indesit's control board detects that the drain pump is not responding or cannot empty the water within the set time during the cycle.
Indesit Dishwasher Error F8E1: Water Heating Fault
Shown when the Indesit dishwasher detects a problem in the heating circuit and cannot reach the temperature of the selected program.
LG Dryer Error dE: Door Not Closing Properly
The dE code on an LG dryer means the door's magnetic sensor doesn't confirm a proper closure, so the program either won't start or stops mid-cycle.
LG Fridge Error Er FS: Defrost Sensor Fault
Er FS on an LG No-Frost fridge means the probe monitoring evaporator temperature during automatic defrost isn't sending a valid reading.
LG Oven Error F1 / F2: Thermistor Fault
The F1 and F2 codes on an LG oven point to a problem with the thermistor that measures cavity temperature, either open circuit (F1) or short circuit (F2).
LG Dishwasher Error IE: Water Inlet Failure
Indicates the LG dishwasher is not receiving enough water during fill, due to a supply cut-off, blockage, or inlet valve failure.
LG Washer Error OE: Water Drainage Issue
Indicates the LG washing machine failed to drain water within the allowed timeframe.
LG Microwave: PF Alert or Flashing Clock After a Power Outage
The PF (Power Failure) alert or the clock flashing 0:00 on an LG microwave simply means the appliance experienced a power interruption and needs the clock reset; it is not a malfunction.
Miele Fridge Error F21: Ice-Making Fault
The F21 code (shown as 01_F21) on Miele fridges with an ice maker indicates the cubes aren't dropping correctly into the bin, usually due to a physical jam.
Miele Dishwasher Error F62: Drainage Fault
The Miele dishwasher cannot pump out dirty water at the end of a program phase, displaying F62 after several failed drain attempts.
Miele Dryer Filter Alert: Lint Filter Saturated
The filter icon lights up on the Miele dryer when the lint filter has trapped enough fiber to noticeably reduce airflow and extend drying time.
Samsung Washer Error 4E / 4C: No Water Supply Detected
Samsung washer fails to sense incoming water stream into tub within initial set period.
Samsung Fridge Error 5E: Defrost Fault / Blocked Drain
Indicates a fault in the fridge's automatic defrost system: the defrost sensor isn't reading the correct temperature, or the drain tube is frozen or blocked, which eventually stops the unit cooling normally.
Samsung Dryer Error 9C1 / 9C2: Irregular Power Voltage
Indicates the Samsung dryer detected a low or irregular mains voltage, usually after a power cut or voltage spike, and halts the cycle to protect the electronic control board.
Samsung Microwave Error SE / dE: Door Switch Fault
The SE or dE code on a Samsung microwave means the control panel detects an inconsistent signal from the door safety switches and locks operation for safety.
Siemens Washer Error E13: Water Leak Detected (Aquastop)
Appears when the Aquastop safety system detects water in the washer's base tray and immediately halts the program to prevent flooding.
Siemens / Bosch Dishwasher Error E15: Aquastop Flood Triggered
Water has accumulated in the lower safety tray beneath appliance, triggering safety float switch.
Siemens Induction Hob Error E9: Cookware Not Detected
The E9 alert on a Siemens induction hob appears when the cooking zone doesn't detect a suitable induction-ready pan, so it won't activate the coil even though the zone is switched on.
Siemens Fridge Temperature Alarm: Door Open or Excess Heat
The Siemens fridge with electronic panel beeps and shows the alarm symbol when it detects a door has been left open too long or internal temperature has risen above the safe range.
Siemens Freezer Alarm P1: Power Failure Warning
The Siemens freezer displays P1 with the alarm light on, warning that an extended power outage occurred and the internal temperature rose above the safe limit.
Siemens Oven: Door Stays Locked After a Pyrolytic Cleaning Cycle
After the pyrolytic cleaning cycle finishes, the padlock symbol stays lit and the Siemens oven door won't unlock even though the cycle is done and the appliance has cooled.
Teka Extractor Hood Filter Alert: Grease Saturation
The Teka hood's filter light or icon turns solid after a set number of usage hours, warning that the metal filters are saturated with grease and reducing suction performance.
Teka Oven: Padlock Symbol Lit and Door Locked
On Teka ovens with a pyrolytic function, the padlock icon lights up to show the door is automatically locked while the interior temperature is still high.
Teka Fridge Error E10: Compartment Not Reaching Temperature
The E10 code appears when the fridge compartment fails to cool sufficiently, usually after an extended power cut or when a large amount of hot food is added.
Teka Washer Error E2: No Water Intake
Triggers when the Teka washer fails to fill the drum with water within the expected time when the program starts.
Whirlpool Dryer Error AF: Airflow Restriction
The AF code (or F4E3 on digital-display models) indicates that drying airflow is restricted, usually from lint buildup in the filter or exhaust duct.
Whirlpool Fridge Error Er FF: Freezer Fan Fault
On Whirlpool combi or side-by-side fridges, Er FF indicates the fan that distributes cold air from the evaporator to the freezer compartment is not spinning correctly.
Whirlpool Washer Error F06: Motor Tachometer Fault
Control module fails to receive speed feedback signals from drum motor tachometer sensor.
Whirlpool Microwave Error F2: Keypad (Touch Panel) Fault
The F2 code on a Whirlpool microwave means the keypad or touch panel sent an incorrect signal to the control board, usually from moisture, grime, or a fault in the panel itself.
Whirlpool Oven Error F3: Temperature Sensor Fault
The F3 code on a Whirlpool oven means the control board has detected an abnormal reading from the cavity's temperature sensor, so it halts the cooking program as a safety measure.
Whirlpool Dishwasher Error F6E1: No Water Intake
Indicates the Whirlpool dishwasher failed to detect enough water intake within the allowed time, stopping the cycle.
Zanussi Fridge Error E09: Freezer Too Warm
The E09 code appears when a Zanussi fridge-freezer's freezer section has been above the safe temperature, usually after a long power cut, warning of possible risk to the food.
Zanussi Washer Error E40: Door Lock Fault
Indicates the Zanussi washer cannot confirm the door is safely closed and locked before or during the program.
Zanussi Freezer Alarm H1 / H2: Temperature Too High
The display flashes H1 or H2 along with an intermittent beep, warning that the internal temperature has risen above the safe freezing level.
Zanussi Dishwasher Error i10: Water Inlet Fault
Appears when the Zanussi dishwasher does not complete the initial water fill within the time allowed by the program.